Day: September 1, 2020

(R)-(+)-N,N-Dimethyl-1-ferrocenylethylamine, cas is 31886-58-5, it is a common heterocyclic compound, the chiral-nitrogen-ligands compound, its synthesis route is as follows.,31886-58-5

(S)-Ugi-amine 1 (5.14g, 20mmol) was dissolved in 50mL of diethyl ether. Under nitrogen and ice salt bath cooling, n-butyl lithium (16mL, 2.5mol / L) was added dropwise to the reaction system, After the completion, the temperature was slowly raised to room temperature, and the reaction was stirred for 3 hours. Chlorodiphenylphosphine (8.82 g, 40 mmol) was added dropwise under ice-cooling, and the mixture was slowly warmed to room temperature and stirred for 12 hours. The reaction was quenched with saturated sodium bicarbonate solution. Extracted with dichloromethane, dried over anhydrous sodium sulfate, concentration, column chromatography to obtain compound 2 (5.38g, 61%).

As the rapid development of chemical substances, we look forward to future research findings about 31886-58-5

Reference£º
Patent; Zhejiang University of Technology; Zhong Weihui; Ling Fei; Nian Sanfei; (14 pag.)CN108774271; (2018); A;,
Chiral nitrogen ligands in late transition metal-catalysed asymmetric synthesis¡ªI. Addressing the problem of ligand lability in rhodium-catalysed hydrosilations
Nitrogen-Containing Ligands for Asymmetric Homogeneous and Heterogeneous Catalysis

Tris[2-(dimethylamino)ethyl]amine, cas is 33527-91-2, it is a common heterocyclic compound, the chiral-nitrogen-ligands compound, its synthesis route is as follows.,33527-91-2

LiBH4 (22 mg, 1 mmol) and Me6TREN (0.52 mL, 2 mmol) wereadded to 5 mL of THF. This was heated to reflux for 1 h at whichpoint the heat and stirrer were turned off. Slow cooling of the solutionyielded X-ray quality colorless crystals (40 mg, 16%).1H NMR (400.1 MHz, C6D6, 300 K): delta 2.11 (s, 18H, Me6TREN Me),1.94, 1.90 (overlapping br s, 12H, Me6TREN CH2), 0.59 ppm(quartet/septet, 4H, BH4, 1J10BH = 27.5 Hz, 1J11BH = 81.5 Hz).13C NMR (100.6 MHz, C6D6, 300 K): delta 57.0 (CH2), 51.2 (CH2),45.7 ppm (Me).7Li NMR (155.5 MHz, C6D6, 300 K): delta 0.29 ppm.11B NMR (128.3 MHz, C6D6, 300 K): delta 39.5 ppm (quin,1JBH = 81.2 Hz).Elemental analysis for C12H34N4LiB: Calc.: C, 57.15; H, 13.59; N,22.22. Found: C, 57.16; H, 13.48; N, 22.59%.

As the rapid development of chemical substances, we look forward to future research findings about 33527-91-2

Reference£º
Article; Kennedy, Alan R.; McLellan, Ross; McNeil, Greg J.; Mulvey, Robert E.; Robertson, Stuart D.; Polyhedron; vol. 103; (2016); p. 94 – 99;,
Chiral nitrogen ligands in late transition metal-catalysed asymmetric synthesis¡ªI. Addressing the problem of ligand lability in rhodium-catalysed hydrosilations
Nitrogen-Containing Ligands for Asymmetric Homogeneous and Heterogeneous Catalysis

N1,N2-Dimethylethane-1,2-diamine, cas is 110-70-3, it is a common heterocyclic compound, the chiral-nitrogen-ligands compound, its synthesis route is as follows.,110-70-3

To an ice-cooled solution of N,N’-dimethyethylenediamine (10 mL, 91.0 mmol) in dry THF (150 mL) was added a solution of Boc2O (4.97 g, 22.8 mmol) in dry THF (50 mL) over 30 minutes. The reaction mixture was stirred for 1 h at 0 C. then at rt overnight, and concentrated in vacuo. The resulting residue was taken up in a mixture of EA and a sat. NH4Cl solution. The organic layer was separated, washed with brine, dried (MgSO4), filtered and concentrated under reduced pressure. FC (10% MeOH in DCM) afforded the title compound as a yellow oil (2.90 g, 17%).LC-MS (analytic A, Zorbax SB-AQ column, acidic conditions): tR=0.50 min; [M+H]+=189.40.

As the rapid development of chemical substances, we look forward to future research findings about 110-70-3

Reference£º
Patent; Aissaoui, Hamed; Boss, Christoph; Corminboeuf, Olivier; Frantz, Marie-Celine; Grisostomi, Corinna; US2011/224210; (2011); A1;,
Chiral nitrogen ligands in late transition metal-catalysed asymmetric synthesis¡ªI. Addressing the problem of ligand lability in rhodium-catalysed hydrosilations
Nitrogen-Containing Ligands for Asymmetric Homogeneous and Heterogeneous Catalysis

N1,N2-Dimethylethane-1,2-diamine, cas is 110-70-3, it is a common heterocyclic compound, the chiral-nitrogen-ligands compound, its synthesis route is as follows.,110-70-3

The compound N,N’-dimethylethylenediamine (20 g, 0.226 mol)Soluble in 100mL of dichloromethane,50 mL of Boc anhydride (14.8 g, 0.068 mol) was added dropwise in an ice water bath.Dichloromethane mixture,Drop the room temperature reaction,The progress of the reaction was monitored by TLC (DCM: MeOH = 10:1). filter,The dry filtrate was concentrated under reduced pressure at 40 C.After the column, the product was 9g.

As the rapid development of chemical substances, we look forward to future research findings about 110-70-3

Reference£º
Patent; Sichuan Bai Li Pharmaceutical Co., Ltd.; Zhu Yi; Li Jie; Wan Weili; Zhuo Shi; Li Gangrui; (28 pag.)CN109106951; (2019); A;,
Chiral nitrogen ligands in late transition metal-catalysed asymmetric synthesis¡ªI. Addressing the problem of ligand lability in rhodium-catalysed hydrosilations
Nitrogen-Containing Ligands for Asymmetric Homogeneous and Heterogeneous Catalysis

33527-91-2, Tris[2-(dimethylamino)ethyl]amine is a chiral-nitrogen-ligands compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated,33527-91-2

To a solution of tris(2-dimethylaminoethyl)amine (0.436 g, 1.89 mmol) in acetonitrile (4 mL) was added 1-bromooctane (1.20 g, 6.22 mmol). The resulting mixture was heated at reflux with stirring for 18 hours, during which time a white solid was observed. After cooling, and the addition of a cold hexanes/acetone mixture (15 mL, 1:1), to the reaction flask, the precipitate was filtered with aBuchner funnel, and rinsed with a cold hexanes/acetone mixture (20 mL, 1:1), resulting in T-8,8,8 (1.45 g, 95%) as a yellow-white wax; ?H NMR (300 MI-Tz, CDC13) oe 4.02-3.94 (m, 6H), 3.63-3.54 (m, 6H), 3.42-3.30 (m, 24H), 1.79-1.67 (m, 6H), 1.41-1.19 (m, 30H), 0.90-0.83 (m, 9H); ?3C NMR (75 MHz, CD3OD) oe 65.3,61.0, 50.1, 46.8, 31.5, 28.9, 26.1, 22.4, 22.3, 13.1; high resolution mass spectrum(ESI) m/z 189.8823 ([Mj3 calculated for [C36H8,N4j3: 189.8815). See also Yoshimura et al., 2012, Langmuir 28:9322-933 1. ?H and ?3C NMR spectra of compound T-8,8,8 can be found in Figure 49.

33527-91-2 Tris[2-(dimethylamino)ethyl]amine 263094, achiral-nitrogen-ligands compound, is more and more widely used in various.

Reference£º
Patent; TEMPLE UNIVERSITY-OF THE COMMONWEALTH SYSTEM OF HIGHER EDUCATION; VILLANOVA UNIVERSITY; WUEST, William, M.; MINBIOLE, Kevin, P.C.; BARBAY, Deanna, L.; (227 pag.)WO2016/172436; (2016); A1;,
Chiral nitrogen ligands in late transition metal-catalysed asymmetric synthesis¡ªI. Addressing the problem of ligand lability in rhodium-catalysed hydrosilations
Nitrogen-Containing Ligands for Asymmetric Homogeneous and Heterogeneous Catalysis

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.33527-91-2,Tris[2-(dimethylamino)ethyl]amine,as a common compound, the synthetic route is as follows.,33527-91-2

General procedure: The copper complex Cu5-1 was dissolved in water, and an excessive amount of an aqueous solution of saturated sodium tetrafluoroborate (manufactured by Wako Pure Chemical Industries, Ltd.) was added while stirring. A precipitated solid was collected by filtering and a copper complex Cu5-72 was obtained.

The synthetic route of 33527-91-2 has been constantly updated, and we look forward to future research findings.

Reference£º
Patent; FUJIFILM Corporation; Sasaki, Kouitsu; Kawashima, Takashi; Hitomi, Seiichi; Shiraishi, Yasuharu; US10215898; (2019); B2;,
Chiral nitrogen ligands in late transition metal-catalysed asymmetric synthesis¡ªI. Addressing the problem of ligand lability in rhodium-catalysed hydrosilations
Nitrogen-Containing Ligands for Asymmetric Homogeneous and Heterogeneous Catalysis

Tris[2-(dimethylamino)ethyl]amine, cas is 33527-91-2, it is a common heterocyclic compound, the chiral-nitrogen-ligands compound, its synthesis route is as follows.,33527-91-2

General procedure: The copper complex Cu5-1 was dissolved in water, and an excessive amount of an aqueous solution of saturated sodium tetrafluoroborate (manufactured by Wako Pure Chemical Industries, Ltd.) was added while stirring. A precipitated solid was collected by filtering and a copper complex Cu5-72 was obtained.

As the rapid development of chemical substances, we look forward to future research findings about 33527-91-2

Reference£º
Patent; FUJIFILM Corporation; Sasaki, Kouitsu; Kawashima, Takashi; Hitomi, Seiichi; Shiraishi, Yasuharu; US10215898; (2019); B2;,
Chiral nitrogen ligands in late transition metal-catalysed asymmetric synthesis¡ªI. Addressing the problem of ligand lability in rhodium-catalysed hydrosilations
Nitrogen-Containing Ligands for Asymmetric Homogeneous and Heterogeneous Catalysis

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.110-70-3,N1,N2-Dimethylethane-1,2-diamine,as a common compound, the synthetic route is as follows.,110-70-3

N, N’-Dimethylethylenediamine (5.00g, 57mmol) was dissolved in CH2Cl2 (25mL) and cooled to 0C. Di-tert-butyl dicarbonate (5.00g, 22mmol) was dissolved in CH2Cl2 (25mL) and added dropwise to the reaction flask at 0C, and then warmed to room temperature and stirred overnight. The reaction solution was quenched with H2O (20mL), and extracted with CH2Cl2 (40mL x 2), and the combined organic layers dried with Na2SO4, filtered and concentrated. The residue was purified by column chromatography on silica gel using CH3OH/CH2Cl2 (1/20, V/V) as eluent to give 2 as colorless oil (4.37g, 81%), 1H NMR (400MHz, CDCl3) delta 3.39-3.36 (m, 2H, CH2), 2.95-2.90 (s, 3H, CH3), 2.76 (m, 2H, CH2), 2.48 (s, 3H, CH3), 1.48 (s, 9H, (CH3)3); HRMS (ESI) m/z [M+H]+ Calcd for C9H21N2O2+: 189.1603. Found: 189.1601.

The synthetic route of 110-70-3 has been constantly updated, and we look forward to future research findings.

Reference£º
Article; Yang, Hao; Ouyang, Yifan; Ma, Hao; Cong, Hui; Zhuang, Chunlin; Lok, Wun-Taai; Wang, Zhe; Zhu, Xuanli; Sun, Yutong; Hong, Wei; Wang, Hao; Bioorganic and Medicinal Chemistry Letters; vol. 27; 20; (2017); p. 4635 – 4642;,
Chiral nitrogen ligands in late transition metal-catalysed asymmetric synthesis¡ªI. Addressing the problem of ligand lability in rhodium-catalysed hydrosilations
Nitrogen-Containing Ligands for Asymmetric Homogeneous and Heterogeneous Catalysis

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.33527-91-2,Tris[2-(dimethylamino)ethyl]amine,as a common compound, the synthetic route is as follows.,33527-91-2

General procedure: The copper complex Cu5-1 was dissolved in water, and an excessive amount of an aqueous solution of saturated sodium tetrafluoroborate (manufactured by Wako Pure Chemical Industries, Ltd.) was added while stirring. A precipitated solid was collected by filtering and a copper complex Cu5-72 was obtained.

As the paragraph descriping shows that 33527-91-2 is playing an increasingly important role.

Reference£º
Patent; FUJIFILM Corporation; Sasaki, Kouitsu; Kawashima, Takashi; Hitomi, Seiichi; Shiraishi, Yasuharu; US10215898; (2019); B2;,
Chiral nitrogen ligands in late transition metal-catalysed asymmetric synthesis¡ªI. Addressing the problem of ligand lability in rhodium-catalysed hydrosilations
Nitrogen-Containing Ligands for Asymmetric Homogeneous and Heterogeneous Catalysis

110-70-3, N1,N2-Dimethylethane-1,2-diamine is a chiral-nitrogen-ligands compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated,110-70-3

In a 1000 ml three-necked flask equipped with a dropping funnel and a magnetic stirrer, 31.9 g (0.233 mol) of phosphorus trichloride and 500 ml of anhydrous diethyl ether were charged at room temperature in a nitrogen gas atmosphere, and the mixture was cooled to 5C or less in an ice bath. While the resulting reaction mixture was stirred, 25.0 ml (0.233 mol) of N,N’-dimethylethylenediamine were slowly added dropwise to the reaction mixture. Furthermore, 65.0 ml (0.465 mol) of triethylamine were slowly added dropwise. After the reaction mixture was further stirred for 1.5 hours, it was filtered under pressure in a nitrogen gas atmosphere. After the resulting crystals were washed with anhydrous diethyl ether three times, they were purified by vacuum-distillation (0.4 kPa, 44-52C), and 16.28 g of chloro(N,N’-dimethylethylenediamino)phosphine were obtained in the form of a transparent liquid; the yield was 46%. The resulting compound was identified with a nuclear magnetic resonance analyzer (BRUKER Ultra Shield 300 NMR Spectrometer, manufactured by BRUKER Limited.). The resulting spectral data are shown below. 1H-NMR (300 MHz, solvent: CDCl3, standard substance: tetramethylsilane) delta 3.32 (d, 4H) 2.78 (d, 6H) 31P-NMR (121 MHz, solvent: CDCl3, standard substance: triphenylphosphine) delta 171.30 (s, 1P) The structural formula is shown below.

110-70-3 N1,N2-Dimethylethane-1,2-diamine 8070, achiral-nitrogen-ligands compound, is more and more widely used in various.

Reference£º
Patent; Kanto Denka Kogyo CO., LTD.; EP1956026; (2008); A1;,
Chiral nitrogen ligands in late transition metal-catalysed asymmetric synthesis¡ªI. Addressing the problem of ligand lability in rhodium-catalysed hydrosilations
Nitrogen-Containing Ligands for Asymmetric Homogeneous and Heterogeneous Catalysis